Christie-digital-systems XENON CONSOLE Manual do Utilizador

DIGITAL SYSTEMS INSTRUCTIONS FOR INSTALLATION AND OPERATION OF SLC SERIES XENON CONSOLE SLC 20/30,40,45,45R,70 TD-641 REV. 6.0 CHRISTIE DIGITAL

SLC Series Xenon Console 2-2 CHRISTIE DIGITAL SYSTEMS August 7, 2003 2.2. ALLOW LAMP TO COOL WARNING If the lamp has been in use, wait at le

CHAPTER NUMBER: TITLE CHRISTIE DIGITAL SYSTEMS 2-3 August 7, 2003 2.5. AVOID FIRE HAZARDS WARNING FIRE HAZARD: Keep hands, clothes, and combustibl

3 CHRISTIE DIGITAL SYSTEMS 3-1 August 7, 2003 3. GENERAL DESCRIPTION This SLC Xenon Console is a series of projection illumination systems that com

4 CHRISTIE DIGITAL SYSTEMS 4-1 August 7, 2003 4. INSTALLATION PROCEDURES 4.1. UNPACKING Follow these instructions if the unit is crated. Christie

SLC Series Xenon Console 4-2 CHRISTIE DIGITAL SYSTEMS August 7, 2003 1: Exhaust Duct Connector (195713-001) 2: Air Switch Assembly (195557-0

4: Installation Procedures CHRISTIE DIGITAL SYSTEMS 4-3 August 7, 2003 1: Air Switch Assy. (195557-001) 2: Igniter, IGA-10 (116715-001) IGA

SLC Series Xenon Console 4-4 CHRISTIE DIGITAL SYSTEMS August 7, 2003 4.2.2. DOOR P ANELS All three door panels are removable for easier acces

4: Installation Procedures CHRISTIE DIGITAL SYSTEMS 4-5 August 7, 2003 4.2.4. MOUNTING THE P ROJECTOR The SLC Console includes a standard projector

Operator’s Manual Xenon Console, Model SLC 20/30,40,45,45R,70 TD641, Rev. 6.0 Manufactured Under U.S. Patents 3,843,879 and 5,054,909 Other Patents

SLC Series Xenon Console 4-6 CHRISTIE DIGITAL SYSTEMS August 7, 2003 AC Wiring Hook-Ups AC AMPERES WIRE DIAMETER (AWG) PER CABLE LENGTH PER P

5 CHRISTIE DIGITAL SYSTEMS 5-1 August 7, 2003 5. ALIGNMENT AND CHECKOUT PROCEDURES 5.1. MECHANICAL ALIGNMENT When installing an SLC console equip

SLC Series Xenon Console 5-2 CHRISTIE DIGITAL SYSTEMS August 7, 2003 1: Igniter, IGA-10 (116715-001) 11: Magnet, Arc Stabilizer (515000-092

4: Alignment and Checkout Procedures CHRISTIE DIGITAL SYSTEMS 5-3 August 7, 2003 6. Remove knurled nut and locking star washer (if present) from n

6 CHRISTIE DIGITAL SYSTEMS 6-1 August 7, 2003 6. OPERATING THE SLC 6.1. SAFETY REVIEW WARNING Do not install, operate, maintain, or repair the SLC

SLC Series Xenon Console 6-2 CHRISTIE DIGITAL SYSTEMS August 7, 2003 SLC 20, 30 SLC 40, 45, 70 1: Meter, 150 Amp (535112-321) 7: Rocker

7: Operating the SLC Xenon Console CHRISTIE DIGITAL SYSTEMS 6-3 August 7, 2003 If the light is not on when the pilot lamp (Item 5 in Figure 6-1)

SLC Series Xenon Console 6-4 CHRISTIE DIGITAL SYSTEMS August 7, 2003 6.3. OPTICAL ALIGNMENT AND ADJUSTMENT Repeat this procedure every time a

7: Operating the SLC Xenon Console CHRISTIE DIGITAL SYSTEMS 6-5 August 7, 2003 6.4. TILT ADJUSTMENT The SLC Console is optionally equipped with a j

CHRISTIE DIGITAL SYSTEMS i August 7, 2003 TABLE OF CONTENTS TABLE OF CONTENTS...

SLC Series Xenon Console 6-6 CHRISTIE DIGITAL SYSTEMS August 7, 2003

7 CHRISTIE DIGITAL SYSTEMS 7-1 August 7, 2003 7. MAINTENANCE AND ADJUSTMENTS WARNING Wear protective clothing when protective cover is removed fr

SLC Series Xenon Console 7-2 CHRISTIE DIGITAL SYSTEMS August 7, 2003 WARNING Always remove the lamp before cleaning the reflector. 7.2.1. CL

7: Operating the SLC Xenon Console CHRISTIE DIGITAL SYSTEMS 7-3 August 7, 2003 These items should be cleaned approximately every six months under n

SLC Series Xenon Console 7-4 CHRISTIE DIGITAL SYSTEMS August 7, 2003 The following adjustments must be made with the rear lamp adjustments c

7: Operating the SLC Xenon Console CHRISTIE DIGITAL SYSTEMS 7-5 August 7, 2003 115 VAC Connect three signal wires (Scope/Flat) from automation prog

SLC Series Xenon Console 7-6 CHRISTIE DIGITAL SYSTEMS August 7, 2003 7.6. OPTIMIZER REFLECTOR The SLC OPTIMIZER reflector is designed to give

8 CHRISTIE DIGITAL SYSTEMS 8-1 August 7, 2003 8. TROUBLESHOOTING This section helps the user to identify and, where possible, correct system malfun

SLC Series Xenon Console 8-2 CHRISTIE DIGITAL SYSTEMS August 7, 2003 8.2. MALFUNCTION: LAMP DOES NOT IGNITE The system powers up, but the lam

CHRISTIE DIGITAL SYSTEMS W-1 August 7, 2003 WARRANTY COVERING THEATRE PRODUCTS MANUFACTURED BY CHRISTIE DIGITAL SYSTEMS (herein referred to as “Ch

SLC Series Xenon Console ii CHRISTIE DIGITAL SYSTEMS August 7, 2003 6.5.1. Removing the Lamp...

SLC Series Xenon Console W-2 CHRISTIE DIGITAL SYSTEMS August 7, 2003

Appendix A CHRISTIE DIGITAL SYSTEMS A-1 August 7, 2003 Appendix A: Assembly Diagrams and Parts Lists Appendix A contains diagrams and parts lists f

SLC Series Xenon Console A-2 CHRISTIE DIGITAL SYSTEMS August 7, 2003 Figure A-1: Autofocus Assembly

Appendix A: Diagrams and Parts Lists CHRISTIE DIGITAL SYSTEMS A-3 August 7, 2003 # Description Part Number 1 Lamp Adjustment Screw, Long 195145

SLC Series Xenon Console A-4 CHRISTIE DIGITAL SYSTEMS August 7, 2003 Figure A-2: SLC Xenon Lamp Console (Front View)

Appendix A: Diagrams and Parts Lists CHRISTIE DIGITAL SYSTEMS A-5 August 7, 2003 # Description Part Number 1 Exhaust Duct Connector, 8.0 in 195

SLC Series Xenon Console A-6 CHRISTIE DIGITAL SYSTEMS August 7, 2003 Figure A-3: SLC Xenon Lamp Console (Rear View)

Appendix A: Diagrams and Parts Lists CHRISTIE DIGITAL SYSTEMS A-7 August 7, 2003 # Description Part Number 1 Air Switch 1600 Assembly 195557-00

SLC Series Xenon Console A-8 CHRISTIE DIGITAL SYSTEMS August 7, 2003 SLC 20, 30 SLC 40, 45, 70 Figure A-4: Control Panel

Appendix A: Diagrams and Parts Lists CHRISTIE DIGITAL SYSTEMS A-9 August 7, 2003 # Description Part Number 1 Meter, 150 Amp, 100 VAC 535112-321

Table of Contents CHRISTIE DIGITAL SYSTEMS iii August 7, 2003 iiiLIST OF FIGURES AND TABLES Figure 2-1: Protective Clothing Safety Kit Contents...

SLC Series Xenon Console A-10 CHRISTIE DIGITAL SYSTEMS August 7, 2003 Figure A-5: Manual Lamp Adjustment Assembly

Appendix A: Diagrams and Parts Lists CHRISTIE DIGITAL SYSTEMS A-11 August 7, 2003 # Description Part Number 1 Adjustment Guide 193571-001 2 Stan

SLC Series Xenon Console A-12 CHRISTIE DIGITAL SYSTEMS August 7, 2003 Figure A-6: Plenum , All Models (Top View)

Appendix A: Diagrams and Parts Lists CHRISTIE DIGITAL SYSTEMS A-13 August 7, 2003 # Description Part Number 1 Igniter, IGA-10 116715-001 Ignit

SLC Series Xenon Console A-14 CHRISTIE DIGITAL SYSTEMS August 7, 2003 Figure A-7: Power Supply

Appendix A: Diagrams and Parts Lists CHRISTIE DIGITAL SYSTEMS A-15 August 7, 2003 # Description Part Number 1 Capacitor (C1) (SLC 20, 30) 530106-

Appendix B CHRISTIE DIGITAL SYSTEMS B-1 AUGUST 7, 2003 Appendix B: Additional Diagrams Appendix B contains additional support information in the fo

SLC Series Xenon Console B-2 CHRISTIE DIGITAL SYSTEMS AUGUST 7,2003 Figure B-1: Schematic Diagram for IGA-10 Igniter (P/N 502519)

Appendix C: Bill of Materials CHRISTIE DIGITAL SYSTEMS B-3 AUGUST 7,2003 Figure B-2: Schematic Diagram for IGA-15M Igniter (P/N 501982)

SLC Series Xenon Console B-4 CHRISTIE DIGITAL SYSTEMS AUGUST 7,2003 Figure B-3: SLC 20-CC20, SLC 30-CC25 Console (Side View) (P35 Projector he

Appendix C: Bill of Materials CHRISTIE DIGITAL SYSTEMS B-5 AUGUST 7,2003 Front View Side View Figure B-4: Console SLC 40-CC40, SLC 45-CC70, SL

1 CHRISTIE DIGITAL SYSTEMS 1-1 August 7, 2003 1. INTRODUCTION 1.1. CONTENTS OF THE MANUAL This manual contains installation, operation, and operato

SLC Series Xenon Console 1-2 CHRISTIE DIGITAL SYSTEMS August 7, 2003 1.3. SPECIAL NOTICES Three kinds of specific notices are used within thi

2 CHRISTIE DIGITAL SYSTEMS 2-1 August 7, 2003 2. SAFETY PRECAUTIONS This section highlights the major dangers of working with the SLC Xenon Console